×
Welcome, Guest

Sign in to learn, create, and do more with the product you love.

Sign In

News & Updates

Filters:
Embedded thumbnail for High-Speed Tuning
How To Work with High-Speed Projects •
High-Speed Tuning

If you use high-speed interfaces like USB 3.0, PCIE, or DDR3/DDR4, you need to use match length tuning to ensure that they work properly. We’ll show you why and how, as well as demonstrating the different tools for length tuning.

Start Watching
Via current carrying capacity for PCBs
Blog •
PCB Via Current-Carrying Capacity: How Hot is Too Hot?

One common question from designers is current-carrying capacity of conductors in a PCB. Trace and via current-carrying capacity are legitimate design points to focus on when designing a new board that will carry high current. The goal is to keep conductor temperatures below some appropriate limit, which then helps keep components on the board cool. Let’s dig into the current state of thermal demands on vias in PCBs and how they compare to internal and external PCB traces.

Read More
Simple Simulation in Altium Designer
On-Demand Webinar •
SPICE Simulation Made Simple

SPICE simulation saves you critical time in the prototyping phase. Understanding your simulation interface makes it simple to analyze how your circuits work in different scenarios. Altium Designer provides an intuitive, dedicated interface to support your simulation verification, setup, and analysis directly in your schematic environment. You also benefit from growing support for popular model formats, as well as generic models, simplifying circuit definition and simulation.

Read More
PCB Shield
Blog •
Phalanx, not Failure: PCB Shielding to Protect Your Design

A combination of good printed circuit board design and good shielding mitigates EMI. Good PCB design for EMI shielding revolves around the layout, the placement of filters, and ground planes. A well-designed PCB minimizes parasitic capacitance and ground loops. Keep reading to learn more about PCB shielding.

Read More
Embedded thumbnail for Using Document Parameters with Draftsman
How to Work with Draftsman •
Using Document Parameters with Draftsman

The Draftsman Editor in Altium Designer uses document parameters to allow fine grain control over the draftsman document. We’ll show you how you can use the document parameters in your Draftsman document. 

Start Watching
Embedded thumbnail for High-Speed Features of Creating a Stack
How To Work with High-Speed Projects •
High-Speed Features of Creating a Stack

The foundation of any high speed design is the layer stack. We’ll show you some of Altium Designer’s powerful layer stack creation features.

Start Watching
Man working in Altium Designer
Blog •
Best Practices in Hardware Version Control Systems

Any project can get very complex, and the PCB design team needs to track revisions throughout a project. Why worry about tracking revisions? In the event you ever receive changes to product functional requirements, major changes are made to your product’s architecture, or you’re ready to finalize the design and prepare for fabrication, it’s best to clone a project at its current state and begin working on a new version. Keeping track of all these design changes in a PCB design project takes the type of hardware version control tools you’ll find in Altium 365™.

Read More
Embedded thumbnail for High-Speed Return Paths
How To Work with High-Speed Projects •
High-Speed Return Paths

For high speed designs it is critical to maintain your return path for adequate signal integrity. We’ll show you how, using best practices and error resolutions in Altium Designer.

Start Watching
Embedded thumbnail for Working with Design Variants
How to Work with Draftsman •
Working with Design Variants

Altium Designer’s Draftsman Document allows for several different board views and variants that you can work with. We’ll show you how to add new variants and work with their properties to display exactly what you need in your Draftsman Document

Start Watching
Embedded thumbnail for Creating Schematics in High-speed Projects
How To Work with High-Speed Projects •
Creating Schematics in High-speed Projects

There are several powerful features in Altium Designer for creating schematics in high speed projects. We’ll show you a few, such as how to utilize nets, net classes, blankets, design rules, and differential pairs.

Start Watching
Copper pour and via stitching
Blog •
Copper Pour and Via Stitching: Do You Need Them in a PCB Layout?

To pour or not to pour, to stitch or not to stitch… Over many years, some common “rules of thumb” have become very popular and, ultimately, taken a bit out of context. Rules of thumb are not always wrong, but taking PCB design recommendations out of context helps justify bad design practices, and it can even affect the producibility of your board. Like many aspects of a physical PCB layout, via stitching and copper pour can be like acid: quite useful if implemented properly, but also dangerous if used indiscriminately.

Read More
Altium Designer Signal Integrity
On-Demand Webinar •
What is High-Speed Design?

The primary source of high-speed problems is not due to high clock frequency but rather the fast rise and fall times of component signals. With fast edge rates, reflections may occur at the receiver side, and when the board routing is dense, crosstalk may become a problem. During this webinar, you'll sharpen your knowledge and develop new skills that you can use to design High-Speed PCB's more efficiently and effectively.

Read More
MOSFET Components
Blog •
Should You Use Power MOSFETs in Series?

Power MOSFETs enable a huge range of electronic systems, specifically in situations where BJTs are not useful or efficient. MOSFETs can be used in high current systems in parallel arrangements, but what about their use in series? Both arrangements of MOSFETs have their pitfalls that designers should consider. Let’s look at MOSFETs in series as they are quite useful in certain systems, but be careful to design your circuits and your PCB for reliability.

Read More
Embedded thumbnail for Creating Connectivity
How to Work with Multichannel Schematic •
Creating Connectivity

Multichannel connectivity can be created in a few different ways. We’ll show you how to create connectivity using ports and net labels efficiently and effectively. 

Start Watching
Embedded thumbnail for Hierarchical Structure for High-Speed Projects
How To Work with High-Speed Projects •
Hierarchical Structure for High-Speed Projects

A Hierarchical structure can make your high speed project much easier to navigate and complete. We’ll show you some tips and tricks for creating and maintaining a high speed. Hierarchical design project.

Start Watching
Embedded thumbnail for Schematic Design Reuse Using Snippets
How to work with Snippets •
Schematic Design Reuse Using Snippets

Snippets allow you to easily reuse circuitry across multiple parts of your designs. We’ll show you how create a new snippets the Schematic and how to connect and annotate it so you can easily bring your circuitry directly into your board.

Start Watching
MLCC controlled ESR capacitor
Blog •
Controlled ESR Capacitors: Should You Use Them for Power Integrity?

I can’t think of a single product I’ve built that doesn’t require capacitors. We often talk a lot about effective series inductance (ESL) in capacitors and its effects on power integrity. What about effective series resistance (ESR)? Is there a technique you can use to determine the appropriate level of resistance, and can you use ESR to your advantage?

Read More
Embedded thumbnail for PCB Design Reuse Using Snippets
How to work with Snippets •
PCB Design Reuse Using Snippets

Snippets give you easy access to reuse circuitry on your PCB. Let’s take a look at how you can create and configure snippets for the PCB, connect a component link with the schematic and update the PCB to include your snippet.

Start Watching
Ground Pour, Impedance and Losses
Blog •
Microstrip Ground Clearance Part 2: How Clearance Affects Losses

If your goal is to hit a target impedance, and you’re worried about how nearby pour might affect impedance, you can get closer than the limits set by the 3W rule. But what are the effects on losses? If the reason for this question isn’t obvious, or if you’re not up-to-date on the finer points of transmission line design, then keep reading to see how nearby ground pour can affect losses in impedance-controlled interconnects.

Read More
Altium Designer Interface
On-Demand Webinar •
What is High-Speed Design?

The primary source of high-speed problems is not due to high clock frequency but rather the fast rise and fall times of component signals. With fast edge rates, reflections may occur at the receiver side, and when the board routing is dense, crosstalk may become a problem. During this webinar, you'll sharpen your knowledge and develop new skills that you can use to design High-Speed PCB's more efficiently and effectively. 

Read More
Blog •
USB to Serial-Over-RJ45 Module

Have you considered converting a USB interface to serial (UART), while delivering data over a custom Ethernet cable and RJ45 connectors? If so, we invite you to check out this article on building a USB to Serial-Over-RJ45 Module. Additionally, you'll find a link to our workspace to explore the entire project.

Read More
Blog •
Pi.MX8 Project - Board Layout Part 1

Our exploration of the Pi.MX8 open-source computer module project progresses. In this third chapter, our focus shifts to the PCB layout preparation of the board. Key topics include defining the layerstack and component break-out routing.

Read More
Blog •
PCB CoDesign Whitepaper

Design faster together with the innovative PCB CoDesign feature, exclusively available in Altium Designer. This cutting-edge functionality seamlessly integrates schematic and PCB design, facilitating concurrent work by multiple engineers on the same project. Learn more about this groundbreaking feature in our comprehensive manual.

Read More
Blog •
How to Test Suspect Electronic Components

Electronic components power nearly everything in our modern lives. However, as long as there are buyers for parts, counterfeiters will persist in their endeavors. Financial losses resulting from fake components are challenging to ascertain due to enforcement limitations and the difficulty in collecting data on the issue. In this article, we demonstrate how to test and verify components in batch orders.

Read More
Blog •
Design Phase – Lid Assembly Electronics Part 2

We are going deeper into lid assembly electronics in our Open Source Laptop project. In this chapter we will tackle the PCB design of the webcam board and show you how to deal with some expected challenges, such as overall small form factor of the board or breaking out the microscopic webcam image sensor.

Read More
Agile Hardware Development
Blog •
5 Ways Hardware Development Is Just… Different

Explore the challenges and strategies of implementing Agile methodology in electronics hardware development. Understand key differences between hardware and software development within the Agile framework.

Read More
Blog •
Flexible Circuit Assembly: Thinking Through Component Placement

The flexible circuits are ideal for applications where a thin, small, and lightweight PCB is needed. However, in such cases, challenges in assembly and fabrication often arise. This article delves into these challenges, focusing on component selection and placement and how they can significantly impact the performance of the flexible circuit in its intended application.

Read More
Blog •
Coding Your Own Networked Test Equipment

Have you ever performed manual tests? If your answer is yes, you're likely aware of how laborious and time-consuming the entire process can be. Allow us to introduce you to the realm of test equipment automation. Our new step-by-step guide empowers you to write code that seamlessly configures your networked test equipment, all from the convenience of your computer.

Read More
Blog •
Pi.MX8 Project – Schematic structure and component placement

We are advancing with our brand new Pi.MX8 Project. In this chapter, we delve deeper into two crucial aspects: the overall schematic and component placement on the PCB board. Don't hesitate to check it out. Additionally, you can follow this project through our workspace; the link is provided within the article.

Read More
Blog •
Redefine PCB Boundaries with HDI Design

Dive into the world of High-Density Interconnect (HDI) design to enhance your projects. Explore heightened signal integrity, improved reliability, and the seamless integration of advanced technologies - all within compact and lightweight designs. Discover more about HDI on our updated feature page.

Read More
Generic Components
What's New in 22.3 •
通用元件

从产生创意到变为实物所需的路程将越来越短。新功能将有助于缩短进行原理图设计所需的时间。

Learn More
Embedded thumbnail for Designing a Silkscreen
DFM and Fabrication Cost/Time Constraints •
Designing a Silkscreen

The silkscreen layer allows you to add text and extra detail that will appear in your final designed board. We'll show you how to get started and what to look for when creating a silkscreen.

Start Watching
Embedded thumbnail for Types of Component Variations
How to work with Variants •
Types of Component Variations

Altium Designer allows you to implement several different types of component variations. We’ll show you the differences between fitted, modified parameters, not fitted, and alternate Part variations, as well as how to add and manage these variations for your design.

Start Watching
Embedded thumbnail for Query Language: Basic Concept Part III
Query Language •
Query Language: Basic Concept Part III

Often the criterion for searching certain objects in Altium Designer is matching parameters to some string (text) values. Learn from this video how to use substitution symbols in queries and increase your productivity when working on projects

Start Watching
Embedded thumbnail for Solder Mask Expansion and Minimum Sliver
DFM and Fabrication Cost/Time Constraints •
Solder Mask Expansion and Minimum Sliver

Using the solder mask expansion and the minimum solder mask sliver rules, you can make sure your solder mask layer doesn’t interfere with any of your exposed copper and is manufacturable.

Start Watching
Embedded thumbnail for Query Language: Basic Concept Part II
Query Language •
Query Language: Basic Concept Part II

Do you want to learn how to make more complex queries consisting of several commands? This video is about auxiliary operators that exist in the Altium Designer query language, and how to combine and use them together.

Start Watching
Embedded thumbnail for Teardrops for DFM
DFM and Fabrication Cost/Time Constraints •
Teardrops for DFM

If you need to increase the width to any primitive, but need to maintain manufacturability, you can use teardrops. We’ll show you how to create a teardrop and specify the shape and size.

Start Watching
Embedded thumbnail for Creating a New Design Variant
How to work with Variants •
Creating a New Design Variant

You can create variants and allow various changes to your design while maintaining all other versions in Altium Designer. We’ll show you how to create new variants using the variant manager and what you need to know to configure your variants correctly.

Start Watching
Embedded thumbnail for Query Language: Basic Concept Part I
Query Language •
Query Language: Basic Concept Part I

In this video you will learn types of query language commands and what they can be used for.

Start Watching
Embedded thumbnail for Configuring the Vias Annular Ring
DFM and Fabrication Cost/Time Constraints •
Configuring the Vias Annular Ring

The minimum dimension from the wall of the aperture to the edge of the pad is called an annular ring, and we can configure it with Altium Designer. We’ll show you how to get started and manage the annular ring in your design rules.

Start Watching
Embedded thumbnail for Design RF PCB: RF Materials for PCB
RF PCB Design •
Design RF PCB: RF Materials for PCB

Unlike an ideal environment, PCB materials introduce losses into the propagated signal. In this, we tried to figure out what materials to choose for RF printed circuit boards.

Start Watching
Embedded thumbnail for Design for Manufacturing (DFM) Overview
DFM and Fabrication Cost/Time Constraints •
Design for Manufacturing (DFM) Overview

During your design process, there are simple steps you can take to focus on Design for Manufacturing, or DFM. Altium Designer has a unique set of tools you can use to make the DFM process efficient ensuring manufacturability. In this overview video, we’ll talk about some of topics covered in upcoming videos about the DFM tools Altium Designer offers you.

Start Watching
Embedded thumbnail for Fixing Broken Component Models
Working with MCAD CoDesigner extension •
Fixing Broken Component Models

If you have a broken component model that won’t transfer properly from ECAD to MCAD, Altium Designer will help. We’ll show you how to use the Make PCB Library tool, the Extract 3D models tool, and your MCAD tool to correct broken components and make them usable.

Start Watching
Embedded thumbnail for Query Language: What is It For?
Query Language •
Query Language: What is It For?

A PCB project contains many different objects. How to manage them? How to find the right ones quickly and efficiently? This video starts the series about query language. Learn the language commands and how to use them and expand your possibilities!

Start Watching
Embedded thumbnail for Maintaining MCAD Constraints During Exchange
Working with MCAD CoDesigner extension •
Maintaining MCAD Constraints During Exchange

The Altium Designer MCAD Co-designer panel and extension give you a few tools to create a model that is unified during the ECAD MCAD Exchange. We'll show you how to make sure your models are transferred correctly across the ECAD MCAD exchange.

Start Watching
Embedded thumbnail for Design RF PCB: Plane Connect -direct
RF PCB Design •
Design RF PCB: Plane Connect -direct

It is bad practice to use thermal reliefs to connect pads in RF path circuits. We'll show you how to quickly and easily change pad-to-polygon connection style to direct connection.

Start Watching
Your search returns no results.