×
Welcome, Guest

Sign in to learn, create, and do more with the product you love.

Sign In

News & Updates

Filters:
Embedded thumbnail for Creating a Schematic Symbol - Placing Designators and Comments
How to create a Schematic Symbol •
Creating a Schematic Symbol - Placing Designators and Comments

Placing your designator or comments can be done automatically, but that doesn’t mean they’re visible. We’ll walk you through how to make them visible and position them correctly no matter what orientation your symbol is with automatic positioning.

Start Watching
Embedded thumbnail for Creating a Schematic Symbol: Adding Additional Parts
How to create a Schematic Symbol •
Creating a Schematic Symbol: Adding Additional Parts

Altium Designer makes it easy to add additional parts to your schematic library. We’ll show you how through copying and configuring your new components through the Pin Editor and the properties panel.

Start Watching
Designing the Next-Generation Electronics
Blog •
A-SAP™ – What do you need to know?

The continued miniaturization of both packaging and component size in next-generation electronics is becoming harder and harder to work around and presents a significant challenge for both PCB designers and PCB fabricators. To effectively navigate the constraints of the traditional subtractive-etch PCB fabrication processes, PCB designs require advanced PCB fabrication capabilities while pushing the limits of finer feature size, higher layer counts, multiple levels of stacked micro vias and increased lamination cycles.

Read More
Embedded thumbnail for Component Placement Control Using Rooms
How to work with Rooms •
Component Placement Control Using Rooms

Rooms give you more control over how and where your components are placed in your PCB. We’ll show you how to use room properties to limit what is allowed in and out of a room using the room definition and custom queries.

Start Watching
Pin-package and Via Delay Values
Blog •
Pin-Package Delay and Via Delay in High Speed Length Tuning

Take a look at the inside of some integrated circuit packages, and you’ll find a number of wires bonded to the semiconductor die and the pads at the edge of the component's package. As a signal traverses makes its way along an interconnect and into a destination circuit, signals need to travel across these bond wires and pads before they are interpreted as a logic state. As you look around the edge of an IC, these bond wires can have different lengths, and they incur different levels of delay and contribute to total jitter.

Read More
Embedded thumbnail for How to work with Differential Pair Classes?
How to Work with Differential Pairs •
How to work with Differential Pair Classes?

Modern boards can contain a large number of differential pairs. For convenience, they are combined into differential pairs classes. In this video, we'll walk you through how to create and apply a differential pair class. 

Start Watching
Embedded thumbnail for Adding Rooms from the Schematic
How to work with Rooms •
Adding Rooms from the Schematic

Rooms can be added directly from the schematic sheet. From the schematic sheet they are pushed to the PCB. Here we'll look at the rooms and component classes generated by default in the schematic, how to add and configure rooms manually, and how to push them to the PCB.

Start Watching
6-Layer PCB Design
Blog •
6-Layer PCB Design Guidelines

Once you’ve run out of room on your 4-layer PCB, it’s time to graduate to a 6-layer board. The additional layer can give you room for more signals, an additional plane pair, or a mix of conductors. How you use these extra layers is less important than how you arrange them in the PCB stackup, as well as how you route on a 6-layer PCB. If you’ve never used a 6-layer board before, or you’ve had EMI troubles with this stackup that are difficult to solve, keep reading to see some 6-layer PCB design guidelines and best practices.

Read More
Component Management
On-Demand Webinar •
Help Ensure The Best Designs With Component Management

There are many aspects to designing a PCB. One of the larger aspects has to do with managing your components. We all need components for our designs, but are those components in our library and designs up-to-date or even purchasable? These questions need to be answered before we can safely use them. If not, we could just be wasting our time designing with invalid components. Altium Designer® has several tools to help you manage the components in your libraries and designs.

Read More
Altium Designer Interface
Blog •
Altium Designer 22.5 Update

We are happy to announce that the Altium Designer 22.5 update is now available. Altium Designer 22.5 continues to focus on improving the user experience, as well as performance and stability of the software, based on feedback from our users. Check out the key new features in the What's New section on the left side of this window!

Read More
Are Hybrid PCB Stackups Reliable?
Blog •
How Reliable is Your Hybrid PCB Stackup?

PCB stackups often incorporate slightly dissimilar materials that could pose a reliability problem. Hybrid PCBs are one case where the PCB stackup will include different materials, typically a standard FR4 laminate and a PTFE laminate for RF PCBs. Designers who want to take the lead on material selection when designing their hybrid stackups should consider these factors that affect reliability. As with any PCB stackup, make sure you get your fabricator involved in the manufacturing process early to ensure reliability problems do not arise during production.

Read More
Embedded thumbnail for How to Draw a Board Outline Using Coordinates
How-To's •
How to Draw a Board Outline Using Coordinates

In this video, we cover how to draw a curve by using coordinates. This can be very helpful when creating a board outline.

Start Watching
Embedded thumbnail for Creating a Schematic Symbol: Mapping out the Component
How to create a Schematic Symbol •
Creating a Schematic Symbol: Mapping out the Component

When creating a schematic symbol, one of your first tasks will be creating a component symbol. We’ll show you how to map out a component in the Schematic Library Editor by creating and configuring the component, adding pins, and creating graphics.

Start Watching
Monte Carlo vs Sensitivity Analysis
Blog •
Monte Carlo Simulation vs. Sensitivity Analysis: What’s the Difference?

In a previous article about circuit simulation and reliability, I looked at how Monte Carlo analysis is commonly used to evaluate circuits that are subject to random variations in component values. Sensitivity analysis is a bit different and it tells you how the operating characteristics of your circuit change in a specific direction. Compared to a Monte Carlo simulation, sensitivity analysis gives you a convenient way to predict exactly how the operating characteristics will change if you were to deliberately increase or decrease the value of a component.

Read More
Embedded thumbnail for How and When to Use Rooms
How to work with Rooms •
How and When to Use Rooms

Rooms are an extremely valuable tool within the Altium Designer PCB environment, but how and when do you use rooms? If you need to control component placement and layout, assign a specific design rule to a group of items, or if you have repeated channels that need similar layouts in your multichannel design, rooms can make it much easier.

Start Watching
Simulation, Build and Test
Blog •
Creating Continuous Integration Pipelines for FPGAs

Field Programmable Gate Arrays, or FPGAs, have become ubiquitous amongst high-speed, real-time digital systems. The speed at which FPGAs operate continues to increase at a dizzying pace but their adoption into Continuous Integration pipelines seems not to trail as closely. In this article we will review the concept of CI pipelines, their application to FPGAs, and look at examples on how to set this up.

Read More
Embedded thumbnail for MCAD CoDesigner Quick Start: Autodesk Fusion 360
Working with MCAD CoDesigner extension •
MCAD CoDesigner Quick Start: Autodesk Fusion 360

MCAD CoDesigner is built to address the challenges of electronic product design by enabling seamless collaboration between your electrical and mechanical engineers. This video will show you how to start collaborate between Altium Designer and Autodesk Fusion 360. 

Start Watching
Embedded thumbnail for Component Placement Control for DFM
DFM and Fabrication Cost/Time Constraints •
Component Placement Control for DFM

Component placement is a crucial part of making sure your design is manufacturable, so you need to be able to control placement. We’ll show you how, through rules and courtyard layers to maintain accessibility and manufacturability in your entire design through component placement control.

Start Watching
Collaborators Visualization
Blog •
Soft Locks [Conflict Prevention] in Altium 365

Conflicts can occur when multiple people work on the same project simultaneously. The user might not realize that they are not looking at the latest version of the documentation, leading to problems later. To address this issue, Altium features an intuitive graphical user interface that allows you to examine conflicts quickly and carefully

Read More
Component Creation
On-Demand Webinar •
Increase Productivity With Easy Component Creation

Component creation is a necessary evil when it comes to design, and it’s something we all need to do. But instead of spending hours creating your components and having them turn into a complete roadblock, let it be just a simple bump on the road. Altium Designer has several tools available to you in order to create the different aspects of a component, including the symbol, footprint, 3D model parametric data, supply chain information, and more

Read More
Blog •
Pi.MX8 Project - Board Layout Part 1

Our exploration of the Pi.MX8 open-source computer module project progresses. In this third chapter, our focus shifts to the PCB layout preparation of the board. Key topics include defining the layerstack and component break-out routing.

Read More
Blog •
PCB CoDesign Whitepaper

Design faster together with the innovative PCB CoDesign feature, exclusively available in Altium Designer. This cutting-edge functionality seamlessly integrates schematic and PCB design, facilitating concurrent work by multiple engineers on the same project. Learn more about this groundbreaking feature in our comprehensive manual.

Read More
Blog •
How to Test Suspect Electronic Components

Electronic components power nearly everything in our modern lives. However, as long as there are buyers for parts, counterfeiters will persist in their endeavors. Financial losses resulting from fake components are challenging to ascertain due to enforcement limitations and the difficulty in collecting data on the issue. In this article, we demonstrate how to test and verify components in batch orders.

Read More
Blog •
Design Phase – Lid Assembly Electronics Part 2

We are going deeper into lid assembly electronics in our Open Source Laptop project. In this chapter we will tackle the PCB design of the webcam board and show you how to deal with some expected challenges, such as overall small form factor of the board or breaking out the microscopic webcam image sensor.

Read More
Agile Hardware Development
Blog •
5 Ways Hardware Development Is Just… Different

Explore the challenges and strategies of implementing Agile methodology in electronics hardware development. Understand key differences between hardware and software development within the Agile framework.

Read More
Blog •
Flexible Circuit Assembly: Thinking Through Component Placement

The flexible circuits are ideal for applications where a thin, small, and lightweight PCB is needed. However, in such cases, challenges in assembly and fabrication often arise. This article delves into these challenges, focusing on component selection and placement and how they can significantly impact the performance of the flexible circuit in its intended application.

Read More
Blog •
Coding Your Own Networked Test Equipment

Have you ever performed manual tests? If your answer is yes, you're likely aware of how laborious and time-consuming the entire process can be. Allow us to introduce you to the realm of test equipment automation. Our new step-by-step guide empowers you to write code that seamlessly configures your networked test equipment, all from the convenience of your computer.

Read More
Blog •
Pi.MX8 Project – Schematic structure and component placement

We are advancing with our brand new Pi.MX8 Project. In this chapter, we delve deeper into two crucial aspects: the overall schematic and component placement on the PCB board. Don't hesitate to check it out. Additionally, you can follow this project through our workspace; the link is provided within the article.

Read More
Blog •
Redefine PCB Boundaries with HDI Design

Dive into the world of High-Density Interconnect (HDI) design to enhance your projects. Explore heightened signal integrity, improved reliability, and the seamless integration of advanced technologies - all within compact and lightweight designs. Discover more about HDI on our updated feature page.

Read More
Blog •
Pi.MX8 Project – Introduction and Overview

Do you have extensive knowledge about the Pi.MX8 module? We're excited to introduce a new series of articles focusing on an innovative approach to utilizing this module. In this inaugural chapter, we provide insights into the preparation for this project and detail the elements that will be used.

Read More
Embedded thumbnail for Configuring Autorecognition
How To Work with Power Analyzer by Keysight •
Configuring Autorecognition

Before using the Power Analyzer by Keysight, it is important to configure certain parameters. In this video, we will demonstrate how to properly set up the software for auto-recognition.

Start Watching
Embedded thumbnail for Adding Power Nets for Simulation
How To Work with Power Analyzer by Keysight •
Adding Power Nets for Simulation

One of the most important things when designing your PCB is to check and measure the quality of electrical power for your project. Power Analyzer by Keysight offers you the ability to simulate how power is distributed on your PCB. In this video, we will show you how to prepare power nets for simulation in Altium Designer.

Start Watching
Embedded thumbnail for How to Use Transmission Lines in RF Design
How-To's •
How to Use Transmission Lines in RF Design

High frequency signals are carried on circuit boards via transmission lines. Learn the differences between standard 50 ohm impedance microstrip lines and coplanar transmission lines in this video. We also explore the best-use cases for coplanar transmission lines, how they impact loss and interference, dielectric thicknesses, and more.

Start Watching
Embedded thumbnail for How to Reverse Engineer a PCB from Gerber Files
How-To's •
How to Reverse Engineer a PCB from Gerber Files

Have you ever done a reverse-engineering? In this video we walk you through the process how to prepare a PCB from Gerber files, using a variety of methods, including via CAMtastic in Altium Designer.

Start Watching
Embedded thumbnail for How to Use Power Regulator Circuits in Series and Parallel
How-To's •
How to Use Power Regulator Circuits in Series and Parallel

In this tutorial video we show you two ways to get more power out of your power supply using power regulator circuits in series and in parallel.

Start Watching
NEW
Embedded thumbnail for Measuring in the PCB
How-To's •
Measuring in the PCB

Altium Designer gives you fine grained control over how you measure object distances in the PCB. When spacing is such a critical aspect of board layout, this control is absolutely necessary. We'll show you how to utilize the measure distance command and measure selected objects, as well as how to measure tracks and faces of 3D bodies.

Start Watching
Embedded thumbnail for Polygon: Polygon Creation
How-To's •
Polygon: Polygon Creation

Learn how to create polygon pours to ensure proper copper distribution on your board.

Start Watching
Embedded thumbnail for How to work with cursors in the simulation results?
How-To's •
How to work with cursors in the simulation results?

Cursors are one of the most indispensable tools for modeling results. They do not require long study, are easy to use and give an instant answer to the main questions.

Start Watching
Embedded thumbnail for 3D view control
How-To's •
3D view control

Learn how to use the 3D display mode of the PCB and learn to control the camera in this mode in this video.

Start Watching
Embedded thumbnail for Query Language: How to Easily Create Expressions
How-To's •
Query Language: How to Easily Create Expressions

In this video the main tools which allow to simplify the process of building a query in Altium Designer will be considered. There are several such tools and each of them has its own limitations and peculiarities of use.

Start Watching
Embedded thumbnail for PCB Classes overview
How-To's •
PCB Classes overview

Are there too many primitives on the board? Having trouble creating design rules? This video gives a brief overview of the classes of primitives that can be created on the board, as well as the possibilities for their further use.

Start Watching
Embedded thumbnail for Creating a BGA Footprint with the Footprint Wizard
How-To's •
Creating a BGA Footprint with the Footprint Wizard

Altium Designer makes it easy to create a BGA footprint using our IPC compliant footprint wizard. We'll show you how easily you can create and modify a BGA footprint using the footprint wizard.

Start Watching
Embedded thumbnail for How to work with Pad Classes on PCB?
How-To's •
How to work with Pad Classes on PCB?

Sometimes it is required to set different design rules for a different set of pads on the board. The easiest way is to use pad classes and in this video we'll show you how easy it is to create and apply them.

Start Watching
Embedded thumbnail for How to work with multivariate calculations?
How-To's •
How to work with multivariate calculations?

Additional modes for obtaining temperature, parametric dependencies and probabilistic distribution by the Monte Carlo method are performed together with basic calculations and allow expanding the possibilities for analyzing design results.

Start Watching
Embedded thumbnail for How to calculate Transient Analysis?
How-To's •
How to calculate Transient Analysis?

Transient Analysis simulates the reaction of a circuit over a period of time. It can be supplemented by Fourier Analysis and the use of Initial Conditions.

Start Watching
Embedded thumbnail for BOM Comments
How-To's •
BOM Comments

Convenient interaction and coordination of the Active BOM with the help of comments is possible both from the web version of the project and from the Altium Designer between participants of the same and different roles.

Start Watching
Your search returns no results.