×
Welcome, Guest

Sign in to learn, create, and do more with the product you love.

Sign In

News & Updates

Filters:
Embedded thumbnail for Back Drilling in Altium Designer
How-To's •
Back Drilling in Altium Designer

In this video, we will learn about Back Drilling technology, how to set up back drilling using the Layer Stack Manager, and how to set up the Stub Length sizes for back drilling by specifying applicable nets using the Design Rules Editor.

Start Watching
Blog •
RF Power Amplifier Module PCB Design

RF power amplifiers can be found in many wireless products, often integrated into chipsets or modems. However, in certain specialized systems, you might require higher power output at a specific frequency. This necessitates a discrete amplifier circuit to deliver that power. In this article, we present an example project for a power amplifier that you can incorporate into your RF project.

Read More
Embedded thumbnail for Distributed - Element Circuits in RF Design
How-To's •
Distributed - Element Circuits in RF Design

The capacitance and inductance of Distributed-Element circuits are determined by the shape and location of different copper elements in the PCB layout, instead of being concentrated in one point in space. Learn how to work with these circuits in Altium Designer.

Start Watching
Blog •
Avoid GIGO in Your PCB Simulation Tools

Simulation tools are extremely useful for understanding electromagnetic behavior in a design. Learn more about how to avoid obtaining inaccurate results during your PCB simulation process.

Read More
Embedded thumbnail for Collaborative Editing
How-To's •
Collaborative Editing

Save time and minimize reworks while teaming up on a PCB design from anywhere in the world. Watch the video for a sneak preview of the new collaborative editing functionality.

Start Watching
Embedded thumbnail for Exporting Results
How To Work with Power Analyzer by Keysight •
Exporting Results

After completing your simulation in Power Analyzer by Keysight, you will likely need to export some of the results for further analysis. In this video, we will show you how to prepare a report once the simulation is done.

Start Watching
Embedded thumbnail for Plane Connect - Direct in RF Design
How-To's •
Plane Connect - Direct in RF Design

Designing high-frequency circuit boards requires a sharp eye toward maintaining signal integrity. Some signal connections are more prone to interruption than others. In this video, you can learn how Altium Designer's Polygon Connect Design Rule and the Thermal Relief option can help in the PCB design process.

Start Watching
Embedded thumbnail for Understanding and Correcting Violations
How To Work with Power Analyzer by Keysight •
Understanding and Correcting Violations

When you finish the Power Analyzer by Keysight simulation process, you may find some design problems. In this video, we will learn how to understand and correct any violations that may arise on your board.

Start Watching
Blog •
Concept Phase – Cooling and Airflow Part 1

Next step in our open-source laptop project is to explain how to design cooling and airflow. In this article, we can show you the first part of this process, such as airflow concept, fan measurement and clearance.

Read More
Embedded thumbnail for Routing Any Angle or Arc in RF Design
How-To's •
Routing Any Angle or Arc in RF Design

High-frequency signals require special consideration when routing. Altium Designer allows you to add RF nets to a net class, then apply design rules. Learn how, as well as some other handy high-frequency routing tips, in this video.

Start Watching
Harness Design
Blog •
Create Connections with Harness Design

Many modern electronics have multiple boards, and connecting those different boards and systems together are harnesses. Learn more about how Altium Designer can help you create harnesses for your own multi-board designs here.

Read More
Embedded thumbnail for Working with Power Analyzer Panel
How To Work with Power Analyzer by Keysight •
Working with Power Analyzer Panel

Learn how to use the Power Analyzer software by Keysight panel. This video explains all the basic instructions and provides helpful hints for using the software effectively.

Start Watching
Embedded thumbnail for Which PCB Materials are used in RF Design
How-To's •
Which PCB Materials are used in RF Design

High frequency signals are carried on circuit boards via transmission lines. Learn the differences between standard 50 ohm impedance microstrip lines and coplanar transmission lines in this video. We also explore the best-use cases for coplanar transmission lines, how they impact loss and interference, dielectric thicknesses, and more.

Start Watching
Embedded thumbnail for Configuring Autorecognition
How To Work with Power Analyzer by Keysight •
Configuring Autorecognition

Before using the Power Analyzer by Keysight, it is important to configure certain parameters. In this video, we will demonstrate how to properly set up the software for auto-recognition.

Start Watching
Blog •
High-Speed PCB Design Tips

Essential tips for high-speed PCB designs, and when you need to start being concerned about how and where you route your traces.

Read More
Introduction to Open Source Laptop Project
Blog •
Introduction to Open Source Laptop Project

We have started a very exciting journey into the creation of an open source laptop project. This project will be an ongoing one, with our community able interactively participate. By utilizing Altium 365 users will be able to view, comment on, and download design files. This will be a great learning experience for new and experienced PCB designers.

Read More
Blog •
Ebook: Routing High-Density Interconnects with Reliable Microvias

HDI PCBs take a particular approach to routing interconnects through multiple layers to ensure reliability during fabrication, assembly, and operation. The critical structure that enables this is microvias, which are prone to failure if not designed properly. In this e-book, readers will receive an initial look at the reasons microvia reliability has come into the spotlight and why HDI PCB designers put reliability first when routing through microvias.

Read More
Blog •
IPC-2221 Calculator for PCB Trace Current and Heating

Aside from impedance and annular ring calculations, one of the other major formulas specified in the IPC 2221 standard relates temperature rise, trace width, and trace current. THere is also the IPC-2152 standard, both include this guidance on designing for thermal reliability, but which standard should we use?

Read More
Blog •
Stripline Impedance Calculator

Striplines provide some advantages over microstrips as they take advantage of natural shielding and coupling from nearby ground plane layers. Although they tend to experience higher losses due to total confinement in the dielectric, they can be thinner due to the high dielectric constant used in internal layers of a PCB. Use our free impedence calculator to help you determine the correct width needed to hit a target impedance.

Read More
Blog •
Which Types of Opto-Isolators Are Right For Your Signal?

An optoisolator is a cool electronic device that can be used to pass information between a diode without passing an electrical current. There are many great applications for these, but do you know which one is right for you?

Read More
Blog •
Properties panel document options in SCH editors

The Properties panel provides access to the properties of documents and objects. The contents of the panel change depending on the active document or the selected object. This blog will quickly go over some of need to know options around the properties panel in the schematic document.

Read More
High-Speed PCB Stackup Design
Blog •
The High-Speed PCB Stackup Design Challenge

Even with all the good guidelines out there for high speed design, there are particular aspects of stackup construction and their relation to building boards that get overlooked. This blog is goes beyond just the typical SI/PI guidelines and looks at these problems from more of an engineering perspective.

Read More
stitching vias
Blog •
Everything You Need to Know About Stitching Vias

Stitching vias are something you often see spread around the surface layer of a PCB, but what are they? and should you be using them? In this guide, we'll go over some of the standard uses of stitching vias and when they should be used in a PCB.

Read More
PCB Stackup Basics
Blog •
PCB Stackup Basics

In comparison to the build-up of a PCB, the stackup is more concerned with the electrical type of each layer, that is are we working with signals, power, or ground. Continue reading to learn how you can optimize your layer stack.

Read More
Embedded thumbnail for Rigid-Flex Board Shape Design in MCAD
Working with MCAD CoDesigner extension •
Rigid-Flex Board Shape Design in MCAD

The MCAD Codesigner allows you to design or edit your board shape in the MCAD environment and have it pushed back to Altium Designer. We’ll show you how to configure the board shape, rigid and flex regions, and mounting holes.

Start Watching
Embedded thumbnail for Design RF PCB: routing (any angle, arc)
RF PCB Design •
Design RF PCB: routing (any angle, arc)

It is worth taking a responsible approach to the shape and size of the RF signal conductors. In this video we will cover some practical aspects of working with routing such nets in Altium Designer.

Start Watching
Embedded thumbnail for Component Placement in Rigid-flex PCB
Working with MCAD CoDesigner extension •
Component Placement in Rigid-flex PCB

With the MCAD CoDesigner you can quickly add and move components from your MCAD tool and update the design automatically in Altium Designer. We’ll show you how to add a new component, move components, change a component’s region in MCAD, and update your design in Altium Designer.

Start Watching
Embedded thumbnail for Transmission lines (coplanar)
RF PCB Design •
Transmission lines (coplanar)

The boards use transmission lines to carry high-frequency signals. In addition to microstrip lines, coplanar transmission lines with a ground reference polygon are often found on boards. Coplanar transmission lines propagate the same wave type as microstrip transmission lines, but the electromagnetic field is more concentrated near the conductor, so coplanar lines have lower losses at high frequencies, less dispersion, and less interference to adjacent circuits.

Start Watching
Embedded thumbnail for How to Reuse Board Shapes in MCAD
Working with MCAD CoDesigner extension •
How to Reuse Board Shapes in MCAD

You can use the MCAD Co-designer panel to reuse your board shape or geometry in your PCB. We’ll show you how to use the MCAD Co-designer panel in Altium Designer and how to copy your board shape and geometry from your MCAD tool to Altium Designer.

Start Watching
Embedded thumbnail for Selection filter - Panel Properties and PCB
How to work with Selection •
Selection filter - Panel Properties and PCB

Learn how to configure the types of selected objects using the Selection Filter. In addition, you will learn about the Post Selection Filter and its features.

Start Watching
Embedded thumbnail for PCB Origins During the ECAD MCAD Exchange
Working with MCAD CoDesigner extension •
PCB Origins During the ECAD MCAD Exchange

Origins can vary from your MCAD tool and Altium Designer. With the MCAD Co-Designer panel Altium Designer can keep track of your origin point and make sure your design changes are exchanged correctly.

Start Watching
Embedded thumbnail for Global Editing Using Find Similar Objects
How to work with Selection •
Global Editing Using Find Similar Objects

Editing multiple objects one by one can be a very time consuming process. Altium Designer makes this easy and efficient with the Find Similar Objects tool, which allows you to globally select and edit multiple objects at once.

Start Watching
Embedded thumbnail for Shaping the PCB in MCAD
Working with MCAD CoDesigner extension •
Shaping the PCB in MCAD

Through the MCAD Co-designer in Altium Designer, you can collaborate with a mechanical engineer to shape the PCB in your MCAD tool and keep it updated in Altium Designer. We’ll show you how in Altium Designer and in your MCAD tool.

Start Watching
Embedded thumbnail for Cross Select Mode
How to work with Selection •
Cross Select Mode

Cross Select Mode is a unique tool that allows for cross-selection of objects between the schematic and PCB thanks to the Altium Unified platform. This makes it easy to look for specific components, as well as take advantage of component placement tools.

Start Watching
Embedded thumbnail for Tools for Efficient Selection
How to work with Selection •
Tools for Efficient Selection

Efficient selection tools can make a difference in how long and how clean your design can be. Learn how to utilize the Edit Select Menu tools in Altium Designer to take control over your layout.

Start Watching
Embedded thumbnail for Tools for Easily Selecting Objects in the PCB
How to work with Selection •
Tools for Easily Selecting Objects in the PCB

Explore more than basic mouse movements by taking a look at the tools that Altium Designer has to offer for making selecting and moving objects in the PCB an easy task. This will increase your productivity and allow you to spend more time designing

Start Watching
Embedded thumbnail for How to Work with The Polygon Manager
Working with Polygons •
How to Work with The Polygon Manager

It is important to have a high-level view of all polygons on the PCB design. The Polygon Manager lets you rename polygons, set their pour order, perform re-pouring or disable pouring on selected polygons, add/scope the polygon connection style and clearance design rules, and add polygon classes for selected polygons.

Start Watching
Embedded thumbnail for Assigning Impedance Profiles for Differential Pairs
How to Work with Differential Pairs •
Assigning Impedance Profiles for Differential Pairs

When you assign an impedance profile to a differential pair you open up several options for control over your routes. We'll show you how to do just that, as well as how to fix errors that may pop up and how to create classes for differential pairs based on assigned impedance profiles.

Start Watching
Embedded thumbnail for How to Highlight or Select Net Connections in the PCB
How-To's •
How to Highlight or Select Net Connections in the PCB

We’ll show you how to highlight net selections so you can easily track where connections are made. We’ll show you how to hide and show nets, and how to use the view configuration and PCB panels to view and highlight nets across your design, and how to assign net colors in both the PCB and the schematic.

Start Watching
Embedded thumbnail for Remove Unused Via Pads
How to Design a BGA •
Remove Unused Via Pads

The Remove Unused Pad Shapes tool in Altium Designer gives you control over the via pads in your design. We’ll show you how to use it to increase the usable area of power and ground polygons, increase the density of conductors between hole rows, and fixing incorrect connections.

Start Watching
Your search returns no results.