Welcome, Guest

Sign in to learn, create, and do more with the product you love.

News & Updates

Filters:
Tag
Article preview
Blog
Bluetooth 5.1 SoC vs. Module: Which is Best for Your Design?

The list of features available in Bluetooth just got a little longer since the release of Bluetooth 5.1. If you want to incorporate a Bluetooth 5.1 SoC into your new product, you have two primary options for bringing this component into your board. The first is as an SoC that mounts to your board just like any other component. The other option is to bring a module into your new board—directly onto the surface layer. Here’s what you need to know about a Bluetooth 5.1 SoC or module in your next IoT product.

Article preview
Blog
USB Power Delivery for Your Next Project

Since its introduction in the late 90s, the USB standard has never ceased to grow in popularity. There has been a growing trend toward USB being a power delivery interface with data, rather than a data interface that can supply power, as the 1.0 specification originally intended. To supply the increasing thirst for power over USB, the USB 3.0 Spec with Type-C began implementing the Power Delivery standard, which you should consider using for your next electronics project.

Article preview
Blog
Circuit Board Design for In-Circuit Testing

There are many types of circuit board tests available in electronics manufacturing today, each having unique goals and characteristics. This article presents guidelines at the design level (schematic and layout) to enable the use of in-circuit testing (ICT) fixtures to verify proper component assembly. These simple test fixtures allow your board to be tested as its assembled, which helps identify and remove failed boards from your production run.

Embedded thumbnail for Creating PCB Mounting Holes
Creating PCB Mounting Holes

Our PCB must somehow be assembled into the final drone assembly. This will be achieved by attaching our PCB to the motherboard connector and by special mounting racks, which requires precise positioning of the two mounting holes on the PCB.

Article preview
Blog
Planning for the Future with Cirris Systems and Altium

Technological advancements have been a hallmark of the past few decades, from the widespread adoption of internet technology to the smartphones and wireless devices we rely on every day to stay connected. Orlan Thatcher, Board Layout Specialist at Cirris Systems, could never have predicted the demand their services would generate. The company struggled with six different software platforms before switching to Altium Designer.

Embedded thumbnail for Working with PCB Keepouts
Working with PCB Keepouts

When working in the PCB, there may be specific areas that you would want to prevent the presence of certain objects, such as vias, tracks or copper regions. All of this can be realized in Altium Designer by using the Keepouts feature.

Article preview
Blog
An Introduction to NFC

I used to work in a research lab that worked primarily with RFID (Radio Frequency IDentification) and NFC (Near Field Communication) technology, particularly for the agriculture industry and cattle identification. These were very specialized fields; however, the lab also worked on projects which involved retail and various other applications for NFC. It’s an amazing technology that you might be using every day without thinking about it - building access to your mobile phone payments, for instance. 

Article preview
Blog
Editing Your PCB Geometry with MCAD Tools

You need to define your PCB geometry in the context of your enclosure. If your board cannot physically be assembled into the final product, it doesn't matter how well laid out it is electrically. This webinar focuses on how the MCAD CoDesigner allows you to edit your PCB in the context of a higher-level assembly, allowing you to respect the relevant mechanical constraints.

Blog
The PCB Fabrication Process — what Every Design Engineer Needs To Know, Part 2

In Part 1 of this article, I described the first steps that occur during the PCB fabrication process. They detailed the inner layer processing effort as well as the efforts that take place during the transition from inner layer processing to lamination. This part of the article will provide a detailed description of the lamination, drilling and plating processes.

Blog
The PCB Fabrication Process—What Every Design Engineer Needs To Know, Part 1

There are still a number of designers - perhaps most of them - who have never toured a PCB fabrication facility. They are also unaware of the various steps that occur during the fabrication process. The purpose of this article is to describe those steps and what transpires in each of them. Part 1 of this article focuses on inner layer processing and the steps that are done prior the lamination process.

Article preview
Blog
Webinar "8 Reasons to Store Your Components in Altium 365"

Working with local libraries seems like a simple solution, but we often don’t take into account the added time spent maintaining libraries and sharing them between team members. This webinar showcases the advantages of component storage in Аltium 365 to resolve the issues of local libraries and component management.

Article preview
Blog
Bridging the Gap Between Designers and Customers

Every piece of electronic equipment starts with a great idea. Transforming great ideas into real, physical products takes a team of talented individuals and multiple companies coming together to make everything from the internal components to the external hardware. Paul Payen de la Garanderie, Founder and Owner of AW Audio, an engineering services company based in France, understands these challenges very well. With an extensive background in the Audio/Visual industry, Paul has had to work with multiple companies over the years, from small start-ups to celebrated AV firms.

Blog
Additive PCB Manufacturing: The Vaccine for Electronics Supply Shocks?

At this time, at least a quarter of the world’s population is under quarantine, with workers unable to go to offices or factories, leading to fundamental disabling of the world economy. The electronics industry is suffering greatly as well, dealing with a supply shock from factories shutting down in Southeast Asia, to demand-side shocks from Western markets literally shutting down. Now it is the electrical engineers taking the lead with additive PCB manufacturing.

Article preview
Blog
Webinar "6 Steps to Master Project Storage"

Altium 365 provides a secure cloud platform to store all of your design files in a single place so you can share them with anyone and access them from anywhere. This webinar discusses the advantages of placing, storing, and working with projects in Altium 365.

Article preview
Blog
Altium Designer 20 Changed My Layout Design Routines

I just finalized my first PCB design using Altium Designer 20. At the same time, I tested some new AD20 features, and in this article, I’ll share my thoughts about new layout design features which made the biggest impression for me: sliding, and any-angle routing.

Article preview
Blog
Designing for Antenna Isolation in Your Wireless System

Anyone who has taken apart an old cell phone or designs IoT devices knows multiple communication capabilities are present in these designs, each requiring different antennas. The RF designer should already take precautions for interconnect isolation, but antenna isolation is just as important when modeling and designing wireless systems.

Blog
PCB Trace and Pad Clearance: Low vs. High Voltage

High voltage/high current designs carry safety requirements which need to be met by designers. Similarly, high speed designs need to have suppressed crosstalk in order to ensure signal integrity. The key design aspects that relate to both areas are your PCB trace clearance and pad clearance values. These design choices are critical for balancing safety, noise suppression, and manufacturability.

Blog
Getting Through PCB DFM

In this article, we’ll discuss the key design features to implement, and steps to take prior to fabrication that will help prevent some DFM process pain.

Altium Designer Getting Started User Guide
Blog
Level Up Your Design Skills - Altium Designer Getting Started User Guide Update
We are happy to announce the new update of our Altium Designer Getting Started User Guide. Whether you are new to Altium Designer or you want to brush up on some topics, the Altium Designer Getting Started User Guide will take you from a beginner to a master in PCB design.  This is only the beginning! This guide will be updated with new information based on user feedback. Let’s first go over the contents of the guide.
Tag
What is Hybrid Beamforming?
Blog
What is Hybrid Beamforming?

In this article, we’ll look at beamforming implementation in an advanced method combining analog and digital techniques, known as hybrid beamforming. This method blends both digital and analog techniques to create multiple beams and thus reach multiple users with varying intensities. In the case of an RF imaging system or a radar system, hybrid beamforming in a MIMO technique also allows tracking of multiple targets with adjustable resolution.

Is your via impedance calculator accurate?
Blog
Why Most Via Impedance Calculators Are Inaccurate

The problem with every via impedance calculator that I have seen is simple: they are incomplete or totally wrong. The “incomplete” part refers to a lack of context; these calculators can roughly reproduce a well-known estimate from a legend like Howard Johnson in his Digital Design textbooks. However, these calculators never provide insight into what they are actually calculating, or where the calculated via impedance is accurate. Keep reading to see why these calculators get it so wrong, as well as the context surrounding via impedance.

Blog
Buck Converter Simulation in Altium Designer

When designing high power circuits (usually very high voltage and/or current), you’ll need to create a regulator from scratch and place it in your PCB layout. It's also the case that you may want to model a real component using discretes in a simulation in order to qualify the system's expected operating regime. As part of buck converter design, you can easily run a buck converter simulation directly in Altium Designer’s schematic editor. Here’s how you can access these features in the newest version of Altium Designer. 

PCIe 6.0 Overview
Blog
Overview of the PCIe 6.0 Standard

Just as you get used to PCIe 5.0, they decide to release another standard! The newest iteration of PCIe is Gen6, or PCIe 6.0. PCIe 6.0 brings a doubling of channel bandwidth through introduction of PAM-4 as the signaling method in high-speed differential channels. This signaling method is a first for PCIe, and it’s an important enabler of the doubled data rate we see in the current standard. In this article, I’ll run over the important points in the standard and what PCB designers can expect when designing these channels.

SPI vs. I2C For Memory Access
Blog
SPI vs. I2C: How to Choose the Best Protocol for Your Memory Chips

One of the common implementations of SPI and I2C in a PCB layout is as a protocol for reading and writing to an external Flash memory. Flash chips are a very common component in embedded systems and can offer high capacities of non-volatile memory up to Gb values. When choosing a memory chip, you'll want to match the application requirements and functionality with the bus speed you need for read and write operations in your memory chip. There is also the matter of the type of Flash memory you'll need to access (NOR vs. NAND).

Blog
Is There an SPI Trace Impedance Requirement?

There is no SPI trace impedance requirement? The reality is that SPI lines only start to need impedance control when the length of the interconnect becomes very long. And because there is no specific impedance requirement in the bus, you have some freedom in channel design and termination. So what exactly qualifies as “very long” and when is some termination method needed? We’ll break it down in this article.

The Skin Effect and EM Fields
Blog
The Skin Effect, Current Density, and the Electromagnetic Field

During this year's AltiumLive CONNECT event, I recall receiving an interesting question about the skin effect and the distribution of current due to the presence of ground in coplanar transmission lines. In this article, we'll look at the electric field around a transmission line carrying a signal, and how this might be impacted by the skin effect.

Packaging for your PCBAs
Blog
What You Need for PCB Packaging and Shipping

When you get your PCBA back from an assembler, you’ll notice the packaging materials used to pack and ship the PCBA. Those materials are specific to electronics, and if you build products on behalf of clients, it’s important to know the packaging materials used for packing and shipping electronics. In this article I’ll show the main set of materials and equipment used to package electronics assemblies.

PCB Output files
Blog
How to Make PCB Gerber Files in Altium Designer Step-by-Step

Once you've got your PCB layout finished and you're ready to start preparing for manufacturing, one of the critical steps is to create PCB Gerber files. When you're ready to create your Gerber files, you need the right set of CAM processor tools that can take data from your PCB layout. In this article, we'll guide you through this process of how to make PCB Gerber files and show some example tasks you might need to perform to generate them.

Teardrops on Differential Pairs?
Blog
Should You Place Teardrops on Differential Pairs?

One of the major factors impacting reliability of a PCBA is the use of teardrops on traces in the PCB. Like many aspects of reliability, the considerations also span into the signal integrity domain, particularly as more high-reliability products require greater data handling capabilities and run at higher speeds. In this article, I’ll break down the issues present in teardrop usage on differential pairs and how these may affect impedance.

Broken PCB
Blog
The High-Reliability PCBA Design and Test Challenge

High-reliability electronics must go through multiple rounds of testing and qualification to ensure they can withstand their intended operating environment. Designing to performance standards, whether the baseline IPC standards or more stringent industry standards, is the first step in ensuring a reliable circuit board. In this e-book, readers will gain a thorough look into PCB testing and analysis, starting from basic tests performed on bare boards and completed assemblies.

Where to place AC Caps on PCIe Lanes
Blog
AC Coupling Capacitors in PCIe Routing

Coupling capacitors find plenty of uses in analog applications and on differential protocols, acting essentially as high pass filters that remove DC bias carried seen on a signal. In the case of PCIe, there are a few reasons to place AC coupling capacitors on differential pairs beyond the fact that AC coupling capacitors are listed in the standard. In this article, we’ll look briefly at where to place coupling capacitors on PCIe links, as well as the reasons these are placed on PCIe links.

Tuning dialog
Blog
Altium Designer 22.7 Update

We are happy to announce that the Altium Designer 22.7 update is now available. Altium Designer 22.7 continues to focus on improving the user experience, as well as performance and stability of the software, based on feedback from our users. Check out the key new features in the What's New section on the left side of this window!

The Positive Impact of Supply Chain Visibility on Design to Cost
Blog
The Positive Impact of Supply Chain Visibility on Design to Cost

Design to cost is a lofty idea that is only perfectly executed when supply and demand for components are in perfect harmony. Unfortunately, the current landscape for component sourcing makes design to cost more of a balancing act rather than an exercise in price reduction. To help designers in their efforts to balance cost, capabilities, and procurement, we created this ebook to help users understand how modern supply chain tools can help in these complex design problems.

Evaluating Stubs on PCIe Lanes
Blog
A Brief Study of Stubs on a PCIe Connector

Stubs are an important topic in high-speed PCB design, and there is a longstanding guideline that stubs should always be removed from all vias on high-speed digital interconnects. While stubs are bad for high-speed lines, they do not always need to be removed. What is more important is to predict the loss profile and frequencies, and to floorplan appropriately to try and prevent such losses.

Surface Layer DFM and Cleanup
Blog
PCB Layout Cleanup Before Manufacturing

Once you finish your placement and routing in your PCB layout, it can be tempting to wrap up the layout and send everything in directly to manufacturing. The reality is that the board may still need some work before it is considered finished. The cleanup you perform at the final stage of PCB layout will help you catch any outstanding errors that can't be programmed into your DRC engine, and it gives you a chance to add any outstanding details to the surface layers.

Tag
Embedded thumbnail for Introduction to Snapping Options
How to use Snapping
Introduction to Snapping Options

Introduction to snapping options: grids, guides, axes of objects, and snapping to objects.

Embedded thumbnail for Working with Tables | Draftsman Document
How to Work with Draftsman
Working with Tables | Draftsman Document

The Draftsman Document Editor allows you to add all your data for your design through tables. We’ll show you how to work with tables, and the various options to add and edit, such as Bill of Materials, Drill Tables, Transmission Line Tables, and custom tables. 

Embedded thumbnail for Pin Part Swapping | High-speed Design
How To Work with High-Speed Projects
Pin Part Swapping | High-speed Design

If you have a lot of traces intersecting on a single layer, but you need to minimize the amount of vias for your high speed design, you can utilize pin and part swapping. Altium Designer has tools to solve these issues, and we’ll show you how to solve them.

Embedded thumbnail for How to Route High-Speed Designs | High-Speed Design
How To Work with High-Speed Projects
How to Route High-Speed Designs | High-Speed Design

Routing for your high-speed design can be really easy with just a little preparation. We’ll walk you through the best ways to set up your routing so you can easily route your high-speed signals. 

Embedded thumbnail for How to Define A Net Class on Schematic | How To Use Altium Designer
How-To's
How to Define A Net Class on Schematic | How To Use Altium Designer

Altium Designer makes it easy to define net classes in both PCB and the schematic. We’ll show you how to define a net class in the schematic for whatever classes you need. 

Embedded thumbnail for Creating Differential Pairs in the Schematic
How to Work with Differential Pairs
Creating Differential Pairs in the Schematic

Learn how to create differential pairs on the schematic side.

Embedded thumbnail for Measuring in the PCB
How-To's
Measuring in the PCB

Altium Designer gives you fine grained control over how you measure object distances in the PCB. When spacing is such a critical aspect of board layout, this control is absolutely necessary. We'll show you how to utilize the measure distance command and measure selected objects, as well as how to measure tracks and faces of 3D bodies.

Embedded thumbnail for Quantel Laser | MCAD and ECAD Designers Collaborate with Altium
Discovering Altium 365
Quantel Laser | MCAD and ECAD Designers Collaborate with Altium

In this video, Quantel’s engineers - Jeremie Waller (Senior Electrical Engineer) is using Altium Designer for ECAD and Laine McNeil (Senior Mechanical Engineer) is using Solidworks for MCAD. They are both in an Altium 365 workspace that allows them to closely collaborate while staying in their own familiar design environment.

Embedded thumbnail for Using Free (Any) Angle Routing
How-To's
Using Free (Any) Angle Routing

In this video, you will see how Altium Designer now makes it extremely easy to create curved corners in your designs. Previously, arc-in-corner routing was only supported during interactive routing, but not in Push&Shove mode or during track sliding. The new Push&Shove engine solves this by adding arcs during push and shove and also during track sliding, which is done by switching to any angle corner mode to perform snake routing.

Embedded thumbnail for Snapping When Creating Routes
How to use Snapping
Snapping When Creating Routes

Learn how to effectively use snapping to facilitate routing.

Embedded thumbnail for How to edit or manage your board shape in Altium Designer | Rigid-flex
How to Work with Rigid-Flex PCBs
How to edit or manage your board shape in Altium Designer | Rigid-flex

Altium Designer 21 features many powerful tools for creating and editing your rigid-flex board shape. We’ll show you how to use to the board planning mode to create board shape and define regions as well as edit their properties for easy identification and functionality.

Embedded thumbnail for How Breville Innovates 4x Faster with Altium
Discovering Altium 365
How Breville Innovates 4x Faster with Altium

Learn how Breville, a consumer electronics company from Australia, was able to speed up its product development process by at least four times with Altium 365. 

Embedded thumbnail for How to use the Property Panel in Altium Designer
How-To's
How to use the Property Panel in Altium Designer

How to use the Property Panel in Altium Designer: The properties panel is your information hub for all objects in Altium Designer. Watch this video to learn how to best use the properties dialog in Altium Designer. 

Embedded thumbnail for How to Improve Routing Using Glossing
How-To's
How to Improve Routing Using Glossing

Routes for your design can get messy, leading to inefficiency and waste. Altium Designer’s Glossing features can help! We’ll show you how to clean up your interactive routing as you route, how to gloss tracks already routed, and some tips and tricks to clean them up exactly how you want them.

Embedded thumbnail for Tenting Vias in Altium Designer
How-To's
Tenting Vias in Altium Designer

This video shows how to tent vias in Altium Designer by using design rules. Since vias are often located very close to pads, during assembly, solder paste sometimes flows into vias, which, in turn, leads to poor soldering quality. To avoid this, cover vias with a solder mask layer.

Embedded thumbnail for How to Create and Validate Return Paths in Altium Designer
How-To's
How to Create and Validate Return Paths in Altium Designer

For high-speed projects where there are lines with a given impedance, it is important to maintain a consistent return signal path. For the return signal, reference planes are created in the form of polygons and the polygons must maintain integrity along the entire path of the signal. This video shows how consistent return paths are created and validated. 

Tag
Your search returns no results.