×
Welcome, Guest

Sign in to learn, create, and do more with the product you love.

Sign In

News & Updates

Filters:
Embedded thumbnail for High-Speed Tuning
How To Work with High-Speed Projects •
High-Speed Tuning

If you use high-speed interfaces like USB 3.0, PCIE, or DDR3/DDR4, you need to use match length tuning to ensure that they work properly. We’ll show you why and how, as well as demonstrating the different tools for length tuning.

Start Watching
Via current carrying capacity for PCBs
Blog •
PCB Via Current-Carrying Capacity: How Hot is Too Hot?

One common question from designers is current-carrying capacity of conductors in a PCB. Trace and via current-carrying capacity are legitimate design points to focus on when designing a new board that will carry high current. The goal is to keep conductor temperatures below some appropriate limit, which then helps keep components on the board cool. Let’s dig into the current state of thermal demands on vias in PCBs and how they compare to internal and external PCB traces.

Read More
Simple Simulation in Altium Designer
On-Demand Webinar •
SPICE Simulation Made Simple

SPICE simulation saves you critical time in the prototyping phase. Understanding your simulation interface makes it simple to analyze how your circuits work in different scenarios. Altium Designer provides an intuitive, dedicated interface to support your simulation verification, setup, and analysis directly in your schematic environment. You also benefit from growing support for popular model formats, as well as generic models, simplifying circuit definition and simulation.

Read More
PCB Shield
Blog •
Phalanx, not Failure: PCB Shielding to Protect Your Design

A combination of good printed circuit board design and good shielding mitigates EMI. Good PCB design for EMI shielding revolves around the layout, the placement of filters, and ground planes. A well-designed PCB minimizes parasitic capacitance and ground loops. Keep reading to learn more about PCB shielding.

Read More
Embedded thumbnail for Using Document Parameters with Draftsman
How to Work with Draftsman •
Using Document Parameters with Draftsman

The Draftsman Editor in Altium Designer uses document parameters to allow fine grain control over the draftsman document. We’ll show you how you can use the document parameters in your Draftsman document. 

Start Watching
Embedded thumbnail for High-Speed Features of Creating a Stack
How To Work with High-Speed Projects •
High-Speed Features of Creating a Stack

The foundation of any high speed design is the layer stack. We’ll show you some of Altium Designer’s powerful layer stack creation features.

Start Watching
Man working in Altium Designer
Blog •
Best Practices in Hardware Version Control Systems

Any project can get very complex, and the PCB design team needs to track revisions throughout a project. Why worry about tracking revisions? In the event you ever receive changes to product functional requirements, major changes are made to your product’s architecture, or you’re ready to finalize the design and prepare for fabrication, it’s best to clone a project at its current state and begin working on a new version. Keeping track of all these design changes in a PCB design project takes the type of hardware version control tools you’ll find in Altium 365™.

Read More
Embedded thumbnail for High-Speed Return Paths
How To Work with High-Speed Projects •
High-Speed Return Paths

For high speed designs it is critical to maintain your return path for adequate signal integrity. We’ll show you how, using best practices and error resolutions in Altium Designer.

Start Watching
Embedded thumbnail for Working with Design Variants
How to Work with Draftsman •
Working with Design Variants

Altium Designer’s Draftsman Document allows for several different board views and variants that you can work with. We’ll show you how to add new variants and work with their properties to display exactly what you need in your Draftsman Document

Start Watching
Embedded thumbnail for Creating Schematics in High-speed Projects
How To Work with High-Speed Projects •
Creating Schematics in High-speed Projects

There are several powerful features in Altium Designer for creating schematics in high speed projects. We’ll show you a few, such as how to utilize nets, net classes, blankets, design rules, and differential pairs.

Start Watching
Copper pour and via stitching
Blog •
Copper Pour and Via Stitching: Do You Need Them in a PCB Layout?

To pour or not to pour, to stitch or not to stitch… Over many years, some common “rules of thumb” have become very popular and, ultimately, taken a bit out of context. Rules of thumb are not always wrong, but taking PCB design recommendations out of context helps justify bad design practices, and it can even affect the producibility of your board. Like many aspects of a physical PCB layout, via stitching and copper pour can be like acid: quite useful if implemented properly, but also dangerous if used indiscriminately.

Read More
Altium Designer Signal Integrity
On-Demand Webinar •
What is High-Speed Design?

The primary source of high-speed problems is not due to high clock frequency but rather the fast rise and fall times of component signals. With fast edge rates, reflections may occur at the receiver side, and when the board routing is dense, crosstalk may become a problem. During this webinar, you'll sharpen your knowledge and develop new skills that you can use to design High-Speed PCB's more efficiently and effectively.

Read More
MOSFET Components
Blog •
Should You Use Power MOSFETs in Series?

Power MOSFETs enable a huge range of electronic systems, specifically in situations where BJTs are not useful or efficient. MOSFETs can be used in high current systems in parallel arrangements, but what about their use in series? Both arrangements of MOSFETs have their pitfalls that designers should consider. Let’s look at MOSFETs in series as they are quite useful in certain systems, but be careful to design your circuits and your PCB for reliability.

Read More
Embedded thumbnail for Creating Connectivity
How to Work with Multichannel Schematic •
Creating Connectivity

Multichannel connectivity can be created in a few different ways. We’ll show you how to create connectivity using ports and net labels efficiently and effectively. 

Start Watching
Embedded thumbnail for Hierarchical Structure for High-Speed Projects
How To Work with High-Speed Projects •
Hierarchical Structure for High-Speed Projects

A Hierarchical structure can make your high speed project much easier to navigate and complete. We’ll show you some tips and tricks for creating and maintaining a high speed. Hierarchical design project.

Start Watching
Embedded thumbnail for Schematic Design Reuse Using Snippets
How to work with Snippets •
Schematic Design Reuse Using Snippets

Snippets allow you to easily reuse circuitry across multiple parts of your designs. We’ll show you how create a new snippets the Schematic and how to connect and annotate it so you can easily bring your circuitry directly into your board.

Start Watching
MLCC controlled ESR capacitor
Blog •
Controlled ESR Capacitors: Should You Use Them for Power Integrity?

I can’t think of a single product I’ve built that doesn’t require capacitors. We often talk a lot about effective series inductance (ESL) in capacitors and its effects on power integrity. What about effective series resistance (ESR)? Is there a technique you can use to determine the appropriate level of resistance, and can you use ESR to your advantage?

Read More
Embedded thumbnail for PCB Design Reuse Using Snippets
How to work with Snippets •
PCB Design Reuse Using Snippets

Snippets give you easy access to reuse circuitry on your PCB. Let’s take a look at how you can create and configure snippets for the PCB, connect a component link with the schematic and update the PCB to include your snippet.

Start Watching
Ground Pour, Impedance and Losses
Blog •
Microstrip Ground Clearance Part 2: How Clearance Affects Losses

If your goal is to hit a target impedance, and you’re worried about how nearby pour might affect impedance, you can get closer than the limits set by the 3W rule. But what are the effects on losses? If the reason for this question isn’t obvious, or if you’re not up-to-date on the finer points of transmission line design, then keep reading to see how nearby ground pour can affect losses in impedance-controlled interconnects.

Read More
Altium Designer Interface
On-Demand Webinar •
What is High-Speed Design?

The primary source of high-speed problems is not due to high clock frequency but rather the fast rise and fall times of component signals. With fast edge rates, reflections may occur at the receiver side, and when the board routing is dense, crosstalk may become a problem. During this webinar, you'll sharpen your knowledge and develop new skills that you can use to design High-Speed PCB's more efficiently and effectively. 

Read More
Blog •
USB to Serial-Over-RJ45 Module

Have you considered converting a USB interface to serial (UART), while delivering data over a custom Ethernet cable and RJ45 connectors? If so, we invite you to check out this article on building a USB to Serial-Over-RJ45 Module. Additionally, you'll find a link to our workspace to explore the entire project.

Read More
Blog •
Pi.MX8 Project - Board Layout Part 1

Our exploration of the Pi.MX8 open-source computer module project progresses. In this third chapter, our focus shifts to the PCB layout preparation of the board. Key topics include defining the layerstack and component break-out routing.

Read More
Blog •
PCB CoDesign Whitepaper

Design faster together with the innovative PCB CoDesign feature, exclusively available in Altium Designer. This cutting-edge functionality seamlessly integrates schematic and PCB design, facilitating concurrent work by multiple engineers on the same project. Learn more about this groundbreaking feature in our comprehensive manual.

Read More
Blog •
How to Test Suspect Electronic Components

Electronic components power nearly everything in our modern lives. However, as long as there are buyers for parts, counterfeiters will persist in their endeavors. Financial losses resulting from fake components are challenging to ascertain due to enforcement limitations and the difficulty in collecting data on the issue. In this article, we demonstrate how to test and verify components in batch orders.

Read More
Blog •
Design Phase – Lid Assembly Electronics Part 2

We are going deeper into lid assembly electronics in our Open Source Laptop project. In this chapter we will tackle the PCB design of the webcam board and show you how to deal with some expected challenges, such as overall small form factor of the board or breaking out the microscopic webcam image sensor.

Read More
Agile Hardware Development
Blog •
5 Ways Hardware Development Is Just… Different

Explore the challenges and strategies of implementing Agile methodology in electronics hardware development. Understand key differences between hardware and software development within the Agile framework.

Read More
Blog •
Flexible Circuit Assembly: Thinking Through Component Placement

The flexible circuits are ideal for applications where a thin, small, and lightweight PCB is needed. However, in such cases, challenges in assembly and fabrication often arise. This article delves into these challenges, focusing on component selection and placement and how they can significantly impact the performance of the flexible circuit in its intended application.

Read More
Blog •
Coding Your Own Networked Test Equipment

Have you ever performed manual tests? If your answer is yes, you're likely aware of how laborious and time-consuming the entire process can be. Allow us to introduce you to the realm of test equipment automation. Our new step-by-step guide empowers you to write code that seamlessly configures your networked test equipment, all from the convenience of your computer.

Read More
Blog •
Pi.MX8 Project – Schematic structure and component placement

We are advancing with our brand new Pi.MX8 Project. In this chapter, we delve deeper into two crucial aspects: the overall schematic and component placement on the PCB board. Don't hesitate to check it out. Additionally, you can follow this project through our workspace; the link is provided within the article.

Read More
Blog •
Redefine PCB Boundaries with HDI Design

Dive into the world of High-Density Interconnect (HDI) design to enhance your projects. Explore heightened signal integrity, improved reliability, and the seamless integration of advanced technologies - all within compact and lightweight designs. Discover more about HDI on our updated feature page.

Read More
Embedded thumbnail for Schematic Design Reuse Using Snippets
How to work with Snippets •
Schematic Design Reuse Using Snippets

Snippets allow you to easily reuse circuitry across multiple parts of your designs. We’ll show you how create a new snippets the Schematic and how to connect and annotate it so you can easily bring your circuitry directly into your board.

Start Watching
Embedded thumbnail for PCB Design Reuse Using Snippets
How to work with Snippets •
PCB Design Reuse Using Snippets

Snippets give you easy access to reuse circuitry on your PCB. Let’s take a look at how you can create and configure snippets for the PCB, connect a component link with the schematic and update the PCB to include your snippet.

Start Watching
Embedded thumbnail for Creating Schematic Channels
How to Work with Multichannel Schematic •
Creating Schematic Channels

Altium Designer makes creating single and multichannel designs effective and quick. We’ll show you how to create and annotate output and input channels in your design. 

Start Watching
Embedded thumbnail for Using Snapping for Primitives and Components | Draftsman Documents
How to Work with Draftsman •
Using Snapping for Primitives and Components | Draftsman Documents

Snapping using the grids and snapping tools in Altium Designer’s Draftsman Editor gives you a lot of control over how you create and annotate primitives and components. We’ll show you how easy it is to use snapping in the Draftsman Editor. 

Start Watching
Embedded thumbnail for Pin Package Delay | High-speed Design
How To Work with High-Speed Projects •
Pin Package Delay | High-speed Design

There are a few things to consider when adding and tuning signal delay to your design. Altium Designer gives you the tools to address the fine tuning for signal delay so you can easily make it work, using pin package delay. 

Start Watching
Embedded thumbnail for Introduction to Snapping Options
How to use Snapping •
Introduction to Snapping Options

Introduction to snapping options: grids, guides, axes of objects, and snapping to objects.

Start Watching
Embedded thumbnail for Working with Tables | Draftsman Document
How to Work with Draftsman •
Working with Tables | Draftsman Document

The Draftsman Document Editor allows you to add all your data for your design through tables. We’ll show you how to work with tables, and the various options to add and edit, such as Bill of Materials, Drill Tables, Transmission Line Tables, and custom tables. 

Start Watching
Embedded thumbnail for Pin Part Swapping | High-speed Design
How To Work with High-Speed Projects •
Pin Part Swapping | High-speed Design

If you have a lot of traces intersecting on a single layer, but you need to minimize the amount of vias for your high speed design, you can utilize pin and part swapping. Altium Designer has tools to solve these issues, and we’ll show you how to solve them.

Start Watching
Embedded thumbnail for How to Route High-Speed Designs | High-Speed Design
How To Work with High-Speed Projects •
How to Route High-Speed Designs | High-Speed Design

Routing for your high-speed design can be really easy with just a little preparation. We’ll walk you through the best ways to set up your routing so you can easily route your high-speed signals. 

Start Watching
Embedded thumbnail for How to Define A Net Class on Schematic | How To Use Altium Designer
How-To's •
How to Define A Net Class on Schematic | How To Use Altium Designer

Altium Designer makes it easy to define net classes in both PCB and the schematic. We’ll show you how to define a net class in the schematic for whatever classes you need. 

Start Watching
Embedded thumbnail for Creating Differential Pairs in the Schematic
How to Work with Differential Pairs •
Creating Differential Pairs in the Schematic

Learn how to create differential pairs on the schematic side.

Start Watching
Embedded thumbnail for Measuring in the PCB
How-To's •
Measuring in the PCB

Altium Designer gives you fine grained control over how you measure object distances in the PCB. When spacing is such a critical aspect of board layout, this control is absolutely necessary. We'll show you how to utilize the measure distance command and measure selected objects, as well as how to measure tracks and faces of 3D bodies.

Start Watching
Embedded thumbnail for Quantel Laser | MCAD and ECAD Designers Collaborate with Altium
Discovering Altium 365 •
Quantel Laser | MCAD and ECAD Designers Collaborate with Altium

In this video, Quantel’s engineers - Jeremie Waller (Senior Electrical Engineer) is using Altium Designer for ECAD and Laine McNeil (Senior Mechanical Engineer) is using Solidworks for MCAD. They are both in an Altium 365 workspace that allows them to closely collaborate while staying in their own familiar design environment.

Start Watching
Embedded thumbnail for Using Free (Any) Angle Routing
How-To's •
Using Free (Any) Angle Routing

In this video, you will see how Altium Designer now makes it extremely easy to create curved corners in your designs. Previously, arc-in-corner routing was only supported during interactive routing, but not in Push&Shove mode or during track sliding. The new Push&Shove engine solves this by adding arcs during push and shove and also during track sliding, which is done by switching to any angle corner mode to perform snake routing.

Start Watching
Embedded thumbnail for Snapping When Creating Routes
How to use Snapping •
Snapping When Creating Routes

Learn how to effectively use snapping to facilitate routing.

Start Watching
Embedded thumbnail for How to edit or manage your board shape in Altium Designer | Rigid-flex
How to Work with Rigid-Flex PCBs •
How to edit or manage your board shape in Altium Designer | Rigid-flex

Altium Designer 21 features many powerful tools for creating and editing your rigid-flex board shape. We’ll show you how to use to the board planning mode to create board shape and define regions as well as edit their properties for easy identification and functionality.

Start Watching
Your search returns no results.