×
Welcome, Guest

Sign in to learn, create, and do more with the product you love.

Sign In

News & Updates

Filters:
Embedded thumbnail for What is the Draftsman Document?
How to Work with Draftsman •
What is the Draftsman Document?

Once your PCB layout is finished it’s time for review. This is where the Draftsman Document and Altium Designer’s Draftsman Editor comes in.

Start Watching
Blog •
Buck Converter Simulation in Altium Designer

When designing high power circuits (usually very high voltage and/or current), you’ll need to create a regulator from scratch and place it in your PCB layout. It's also the case that you may want to model a real component using discretes in a simulation in order to qualify the system's expected operating regime. As part of buck converter design, you can easily run a buck converter simulation directly in Altium Designer’s schematic editor. Here’s how you can access these features in the newest version of Altium Designer. 

Read More
Embedded thumbnail for Adding Project Modules to a Multi-board Schematic
How to work with Multiboard •
Adding Project Modules to a Multi-board Schematic

If you’re using multiple PCBs in your Multi-board design, Altium Designer allows you to add existing projects directly to your schematic with modules. We’ll show you how to quickly and efficiently add these projects to your Multi-board design.

Start Watching
PCIe 6.0 Overview
Blog •
Overview of the PCIe 6.0 Standard

Just as you get used to PCIe 5.0, they decide to release another standard! The newest iteration of PCIe is Gen6, or PCIe 6.0. PCIe 6.0 brings a doubling of channel bandwidth through introduction of PAM-4 as the signaling method in high-speed differential channels. This signaling method is a first for PCIe, and it’s an important enabler of the doubled data rate we see in the current standard. In this article, I’ll run over the important points in the standard and what PCB designers can expect when designing these channels.

Read More
Embedded thumbnail for Checking for Creepage in High Voltage Designs
How-To's •
Checking for Creepage in High Voltage Designs

High voltage devices have leakage currents that propage over the surface of the board. In such devices, it's important to consider not only the standard gap between the two topological elements, but also the shortest possible path between them, taking into account cut-outs and holes. With Altium Designer 20, you can check for creepage using the new creepage distance rule.

Start Watching
Embedded thumbnail for Creating BGA Footprints with the Footprint Wizard
How to create a PCB Footprint •
Creating BGA Footprints with the Footprint Wizard

Altium Designer makes it easy to create a BGA footprint using our IPC compliant footprint wizard. We'll show you how easily you can create and modify a BGA footprint using the footprint wizard.

Start Watching
SPI vs. I2C For Memory Access
Blog •
SPI vs. I2C: How to Choose the Best Protocol for Your Memory Chips

One of the common implementations of SPI and I2C in a PCB layout is as a protocol for reading and writing to an external Flash memory. Flash chips are a very common component in embedded systems and can offer high capacities of non-volatile memory up to Gb values. When choosing a memory chip, you'll want to match the application requirements and functionality with the bus speed you need for read and write operations in your memory chip. There is also the matter of the type of Flash memory you'll need to access (NOR vs. NAND).

Read More
On-Demand Webinar •
Tips & Tricks: Board Shape Creation

Being able to design a board in your ECAD environment doesn’t mean that it is manufacturable in real life. You have to make sure your CAD representation won’t have any problems in the real world by taking some precautions. For example, there are certain areas that need to be free of components and have specified clearances like your board edge. This webinar will help you get acquainted with the creation and modification of your board shape so that you can ensure manufacturability.

Read More
Blog •
Is There an SPI Trace Impedance Requirement?

There is no SPI trace impedance requirement? The reality is that SPI lines only start to need impedance control when the length of the interconnect becomes very long. And because there is no specific impedance requirement in the bus, you have some freedom in channel design and termination. So what exactly qualifies as “very long” and when is some termination method needed? We’ll break it down in this article.

Read More
Embedded thumbnail for How to Remove Unused Pad Shapes
How-To's •
How to Remove Unused Pad Shapes

Unused pad shapes can cause distortion among other problems so it is best to exclude them from your designs. This video shows how to remove unused pad shapes.

Start Watching
Embedded thumbnail for Stackup Presets and Templates
How to work with Layer Stack Manager •
Stackup Presets and Templates

In this video, we will learn how to apply predefined layer stacks to the board, as well as how to save the layer stack file as a template.

Start Watching
The Skin Effect and EM Fields
Blog •
The Skin Effect, Current Density, and the Electromagnetic Field

During this year's AltiumLive CONNECT event, I recall receiving an interesting question about the skin effect and the distribution of current due to the presence of ground in coplanar transmission lines. In this article, we'll look at the electric field around a transmission line carrying a signal, and how this might be impacted by the skin effect.

Read More
Embedded thumbnail for Creating a PCB Footprint Assembly Drawing
How to create a PCB Footprint •
Creating a PCB Footprint Assembly Drawing

If you need to create an assembly drawing of your PCB Footprint for your outjob files we can show you how in Altium Designer. We’ll walk through all the different options for your assembly drawing in your Draftsman document, how to create your assembly drawing and assign it designators.

Start Watching
Packaging for your PCBAs
Blog •
What You Need for PCB Packaging and Shipping

When you get your PCBA back from an assembler, you’ll notice the packaging materials used to pack and ship the PCBA. Those materials are specific to electronics, and if you build products on behalf of clients, it’s important to know the packaging materials used for packing and shipping electronics. In this article I’ll show the main set of materials and equipment used to package electronics assemblies.

Read More
Embedded thumbnail for Using the ActiveBOM
How-To's •
Using the ActiveBOM

Using the ActiveBOM: The Bill of Materials (BOM) contains a list of all the components with their designators, part numbers, values, and other parameters. An ActiveBOM manages the mapping from the design component (part) to the part that is purchased. This video describes how to use the ActiveBOM document to create an up-to-date list of components needed for your project.

Start Watching
Embedded thumbnail for Using Back Drills in your Stackup
How to work with Layer Stack Manager •
Using Back Drills in your Stackup

In this video, we will learn about Back Drilling technology, how to set up back drilling using the layer stack manager, and how to set up the Stub Length sizes for back drilling by specifying applicable nets using the Design Rules Editor.

Start Watching
PCB Output files
Blog •
How to Make PCB Gerber Files in Altium Designer Step-by-Step

Once you've got your PCB layout finished and you're ready to start preparing for manufacturing, one of the critical steps is to create PCB Gerber files. When you're ready to create your Gerber files, you need the right set of CAM processor tools that can take data from your PCB layout. In this article, we'll guide you through this process of how to make PCB Gerber files and show some example tasks you might need to perform to generate them.

Read More
Component composition
On-Demand Webinar •
Help Ensure The Best Designs With Component Management

There are many aspects to designing a PCB. One of the larger aspects has to do with managing your components. We all need components for our designs, but are those components in our library and designs up-to-date or even purchasable? These questions need to be answered before we can safely use them. Altium Designer® has several tools to help you manage the components in your libraries and designs.

Read More
Teardrops on Differential Pairs?
Blog •
Should You Place Teardrops on Differential Pairs?

One of the major factors impacting reliability of a PCBA is the use of teardrops on traces in the PCB. Like many aspects of reliability, the considerations also span into the signal integrity domain, particularly as more high-reliability products require greater data handling capabilities and run at higher speeds. In this article, I’ll break down the issues present in teardrop usage on differential pairs and how these may affect impedance.

Read More
Embedded thumbnail for How to Customize The Properties Panel
How-To's •
How to Customize The Properties Panel

How to Customize The Properties Panel: This video will go over how to customize the look and feel of the properties panel in Altium Designer. By being able to personalize your workspace you can greatly improve your efficiency

Start Watching
Blog •
USB to Serial-Over-RJ45 Module

Have you considered converting a USB interface to serial (UART), while delivering data over a custom Ethernet cable and RJ45 connectors? If so, we invite you to check out this article on building a USB to Serial-Over-RJ45 Module. Additionally, you'll find a link to our workspace to explore the entire project.

Read More
Blog •
Pi.MX8 Project - Board Layout Part 1

Our exploration of the Pi.MX8 open-source computer module project progresses. In this third chapter, our focus shifts to the PCB layout preparation of the board. Key topics include defining the layerstack and component break-out routing.

Read More
Blog •
PCB CoDesign Whitepaper

Design faster together with the innovative PCB CoDesign feature, exclusively available in Altium Designer. This cutting-edge functionality seamlessly integrates schematic and PCB design, facilitating concurrent work by multiple engineers on the same project. Learn more about this groundbreaking feature in our comprehensive manual.

Read More
Blog •
How to Test Suspect Electronic Components

Electronic components power nearly everything in our modern lives. However, as long as there are buyers for parts, counterfeiters will persist in their endeavors. Financial losses resulting from fake components are challenging to ascertain due to enforcement limitations and the difficulty in collecting data on the issue. In this article, we demonstrate how to test and verify components in batch orders.

Read More
Blog •
Design Phase – Lid Assembly Electronics Part 2

We are going deeper into lid assembly electronics in our Open Source Laptop project. In this chapter we will tackle the PCB design of the webcam board and show you how to deal with some expected challenges, such as overall small form factor of the board or breaking out the microscopic webcam image sensor.

Read More
Agile Hardware Development
Blog •
5 Ways Hardware Development Is Just… Different

Explore the challenges and strategies of implementing Agile methodology in electronics hardware development. Understand key differences between hardware and software development within the Agile framework.

Read More
Blog •
Flexible Circuit Assembly: Thinking Through Component Placement

The flexible circuits are ideal for applications where a thin, small, and lightweight PCB is needed. However, in such cases, challenges in assembly and fabrication often arise. This article delves into these challenges, focusing on component selection and placement and how they can significantly impact the performance of the flexible circuit in its intended application.

Read More
Blog •
Coding Your Own Networked Test Equipment

Have you ever performed manual tests? If your answer is yes, you're likely aware of how laborious and time-consuming the entire process can be. Allow us to introduce you to the realm of test equipment automation. Our new step-by-step guide empowers you to write code that seamlessly configures your networked test equipment, all from the convenience of your computer.

Read More
Blog •
Pi.MX8 Project – Schematic structure and component placement

We are advancing with our brand new Pi.MX8 Project. In this chapter, we delve deeper into two crucial aspects: the overall schematic and component placement on the PCB board. Don't hesitate to check it out. Additionally, you can follow this project through our workspace; the link is provided within the article.

Read More
Blog •
Redefine PCB Boundaries with HDI Design

Dive into the world of High-Density Interconnect (HDI) design to enhance your projects. Explore heightened signal integrity, improved reliability, and the seamless integration of advanced technologies - all within compact and lightweight designs. Discover more about HDI on our updated feature page.

Read More
Embedded thumbnail for Rigid-Flex Board Shape Design in MCAD
Working with MCAD CoDesigner extension •
Rigid-Flex Board Shape Design in MCAD

The MCAD Codesigner allows you to design or edit your board shape in the MCAD environment and have it pushed back to Altium Designer. We’ll show you how to configure the board shape, rigid and flex regions, and mounting holes.

Start Watching
Embedded thumbnail for Design RF PCB: routing (any angle, arc)
RF PCB Design •
Design RF PCB: routing (any angle, arc)

It is worth taking a responsible approach to the shape and size of the RF signal conductors. In this video we will cover some practical aspects of working with routing such nets in Altium Designer.

Start Watching
Embedded thumbnail for Component Placement in Rigid-flex PCB
Working with MCAD CoDesigner extension •
Component Placement in Rigid-flex PCB

With the MCAD CoDesigner you can quickly add and move components from your MCAD tool and update the design automatically in Altium Designer. We’ll show you how to add a new component, move components, change a component’s region in MCAD, and update your design in Altium Designer.

Start Watching
Embedded thumbnail for Transmission lines (coplanar)
RF PCB Design •
Transmission lines (coplanar)

The boards use transmission lines to carry high-frequency signals. In addition to microstrip lines, coplanar transmission lines with a ground reference polygon are often found on boards. Coplanar transmission lines propagate the same wave type as microstrip transmission lines, but the electromagnetic field is more concentrated near the conductor, so coplanar lines have lower losses at high frequencies, less dispersion, and less interference to adjacent circuits.

Start Watching
Embedded thumbnail for How to Reuse Board Shapes in MCAD
Working with MCAD CoDesigner extension •
How to Reuse Board Shapes in MCAD

You can use the MCAD Co-designer panel to reuse your board shape or geometry in your PCB. We’ll show you how to use the MCAD Co-designer panel in Altium Designer and how to copy your board shape and geometry from your MCAD tool to Altium Designer.

Start Watching
Embedded thumbnail for Selection filter - Panel Properties and PCB
How to work with Selection •
Selection filter - Panel Properties and PCB

Learn how to configure the types of selected objects using the Selection Filter. In addition, you will learn about the Post Selection Filter and its features.

Start Watching
Embedded thumbnail for PCB Origins During the ECAD MCAD Exchange
Working with MCAD CoDesigner extension •
PCB Origins During the ECAD MCAD Exchange

Origins can vary from your MCAD tool and Altium Designer. With the MCAD Co-Designer panel Altium Designer can keep track of your origin point and make sure your design changes are exchanged correctly.

Start Watching
Embedded thumbnail for Global Editing Using Find Similar Objects
How to work with Selection •
Global Editing Using Find Similar Objects

Editing multiple objects one by one can be a very time consuming process. Altium Designer makes this easy and efficient with the Find Similar Objects tool, which allows you to globally select and edit multiple objects at once.

Start Watching
Embedded thumbnail for Shaping the PCB in MCAD
Working with MCAD CoDesigner extension •
Shaping the PCB in MCAD

Through the MCAD Co-designer in Altium Designer, you can collaborate with a mechanical engineer to shape the PCB in your MCAD tool and keep it updated in Altium Designer. We’ll show you how in Altium Designer and in your MCAD tool.

Start Watching
Embedded thumbnail for Cross Select Mode
How to work with Selection •
Cross Select Mode

Cross Select Mode is a unique tool that allows for cross-selection of objects between the schematic and PCB thanks to the Altium Unified platform. This makes it easy to look for specific components, as well as take advantage of component placement tools.

Start Watching
Embedded thumbnail for Tools for Efficient Selection
How to work with Selection •
Tools for Efficient Selection

Efficient selection tools can make a difference in how long and how clean your design can be. Learn how to utilize the Edit Select Menu tools in Altium Designer to take control over your layout.

Start Watching
Embedded thumbnail for Tools for Easily Selecting Objects in the PCB
How to work with Selection •
Tools for Easily Selecting Objects in the PCB

Explore more than basic mouse movements by taking a look at the tools that Altium Designer has to offer for making selecting and moving objects in the PCB an easy task. This will increase your productivity and allow you to spend more time designing

Start Watching
Embedded thumbnail for How to Work with The Polygon Manager
Working with Polygons •
How to Work with The Polygon Manager

It is important to have a high-level view of all polygons on the PCB design. The Polygon Manager lets you rename polygons, set their pour order, perform re-pouring or disable pouring on selected polygons, add/scope the polygon connection style and clearance design rules, and add polygon classes for selected polygons.

Start Watching
Embedded thumbnail for Assigning Impedance Profiles for Differential Pairs
How to Work with Differential Pairs •
Assigning Impedance Profiles for Differential Pairs

When you assign an impedance profile to a differential pair you open up several options for control over your routes. We'll show you how to do just that, as well as how to fix errors that may pop up and how to create classes for differential pairs based on assigned impedance profiles.

Start Watching
Embedded thumbnail for How to Highlight or Select Net Connections in the PCB
How-To's •
How to Highlight or Select Net Connections in the PCB

We’ll show you how to highlight net selections so you can easily track where connections are made. We’ll show you how to hide and show nets, and how to use the view configuration and PCB panels to view and highlight nets across your design, and how to assign net colors in both the PCB and the schematic.

Start Watching
Embedded thumbnail for Remove Unused Via Pads
How to Design a BGA •
Remove Unused Via Pads

The Remove Unused Pad Shapes tool in Altium Designer gives you control over the via pads in your design. We’ll show you how to use it to increase the usable area of power and ground polygons, increase the density of conductors between hole rows, and fixing incorrect connections.

Start Watching
Your search returns no results.